Bosch Siemens Oven Programmed Control Module PCB 11029080

Bosch Siemens programmed oven control module 11029080 is a replacement electronic circuit board for selected built-in ovens. This module forms part of the oven’s electronic control system and is supplied as a complete programmed assembly. It may be required where a technician has confirmed an internal board fault after checking the power supply, wiring and connected components.

The supplier compatibility list includes your Bosch HRG6767S2A/58. Confirm the full E-Nr, FD number and original module identification before ordering. The relay photograph alone does not establish that this is the board requiring replacement. 

Key Features

• Part number: 11029080
• Programmed electronic control module
• For selected Bosch and Siemens ovens
• Complete PCB assembly, rather than an individual relay
• Model-specific replacement requiring compatibility checks
• Common Signs You May Need a Replacement
• Oven fails to operate despite a confirmed correct power supply
• Selected functions fail after connected components have tested correctly
• Intermittent operation traced to the control board
• Damaged board connectors, tracks or components
• Persistent electronic faults confirmed through technician diagnosis

These symptoms can also result from faulty elements, sensors, fans, wiring, safety devices or other electronic modules. Replacing the PCB without diagnosis may not resolve the problem.

Technical Information

The NF7 100 E24 marking in your earlier photograph identifies an individual relay. It is not the Bosch spare-part number for the complete PCB.

Fault Finding

A qualified appliance technician should:

1. Record the symptoms and complete displayed error message before disconnecting power.
2. Check the appliance supply, terminal connections and relevant safety devices.
3. Inspect the PCB and wiring for loose connections, overheating, corrosion or moisture damage.
4. Test the affected loads, such as heating elements and fan motors, together with their wiring and sensors.
5. Check communication and connections between the oven’s electronic modules.
6. Identify and correct any external fault before installing a replacement board.

Do not bypass safety devices or energise the exposed board for informal testing.

Error Code Information

There is no verified error code that uniquely confirms failure of 11029080.

Bosch advises that electronic fault messages beginning with “D” or “E” should be recorded in full. If a message returns after switching the appliance off and on, further service diagnosis is required. A displayed code does not by itself confirm that this PCB needs replacement.

Control Power Module Safety Notice

*NOTE: ELECTRONIC AND ELECTRICAL PARTS ARE NOT REFUNDABLE OR EXCHANGEABLE* 

BSH service document 9001380162 warns that the control power module’s capacitors may retain a dangerous voltage of up to 360 V DC if the integrated controller has failed. Disconnecting the oven from the mains does not guarantee that the module is safe to handle.

• Installation and testing must be performed by qualified electrical service personnel.
• Before removing or touching the module, the technician must verify that stored voltage has been safely discharged using the manufacturer’s service procedure.
• Do not touch PCB tracks, terminals or components until electrical safety has been confirmed.
• Do not attempt to discharge capacitors by shorting terminals with a screwdriver or other improvised tool.

The supplied notice covers EOX6 (IC6) and EOX5 appliances. The technician must confirm its applicability to the oven being repaired and follow the complete BSH service instructions.

Installation Guidance

Installation must be completed by a qualified appliance technician using the service instructions for the exact E-Nr.

1. Isolate the oven from electricity and verify that it is safely disconnected.
2. Allow the appliance to cool before accessing the electronics.
3. Confirm the replacement part against the complete model, FD number and original module details.
4. Photograph and label the wiring before disconnecting the old module.
5. Release the board from its carrier without damaging plugs, retaining clips or wiring.
6. Install the replacement using appropriate electrostatic protection. Reconnect each plug in its correct position.
7. Complete any specified configuration or commissioning procedure.
8. Refit all covers and carry out electrical safety and functional checks before returning the oven to service.

A programmed module should not be assumed to require no commissioning.

Compatibility – check the complete model number, including the two digits after the slash.

Compatible with the following Bosch models:

HRG6753S1/35 HRG675BS1/35 HRG675BS1/40 HRG675BS1/52 HRG675BS1/58 HRG675BS1S/35 HRG675BS1S/40 HRG675BS1S/49 HRG675BS1S/52 HRG675BS1S/58 HRG6767S2/35 HRG6767S2/40 HRG6767S2/52 HRG6767S2/58 HRG6767S2A/35 HRG6767S2A/40 HRG6767S2A/47 HRG6767S2A/49 HRG6767S2A/50 HRG6767S2A/52 HRG6767S2A/58 HRG6769S1I/35 HRG6769S2/35 HRG6769S2/40 HRG6769S2/52 HRG6769S2/58 HRG6769S2B/35 HRG6769S2B/40 HRG6769S2B/49 HRG6769S2F/35 HRG6769S2F/40 HRG6769S2F/49 HRG6769S2F/52 HRG6769S2F/58 HRG6769S6/35 HRG6769S6/40 HRG6769S6/41 HRG6769S6/49 HRG6769S6/50 HRG6769S6/52 HRG6769S6/58 HRG6769S6B/35 HRG6769S6B/40 HRG6769S6B/41 HRG6769S6B/49 HRG6769S6B/50 HRG6769S6B/58

Compatible with the following Siemens models:

HR678GES6B/35 HR678GES6B/40 HR678GES6B/41 HR678GES6B/52 HR678GES6B/58

These exact model references come from the supplier’s compatibility catalogue.

Meta description: Bosch Siemens programmed oven control module PCB 11029080 for selected models including HRG6767S2A/58. Confirm full E-Nr and board details before ordering.